Genuine E3D Retailer
Genuine BondTech Retailer
Genuine Dyze Design Retailer
Hotend parts: Heatbreak, nozzles, fans, ducts, thermistors, heater cartrides, and PTFE tubing.
1.75mm Bowden Tubing
The bowden tubing is sold in 100mm sections. What is a Bowden feed? A quick explanation: In the realm of 3D printing there are two separate ways to get your filament to the hotend. One is right out of a motor with a...
12VDC Heater Cartridge
A 12VDC 40W heater cartridge with one meter leads. These are used in a number of hotends. High power ceramic heater cartridge with silicon insulated high temperature wires.
2-Wire Fan (5V, 12V or 24 volt DC)
These are great little fans to keep you cool. The fan's shaft rides on two ball bearings to provide a long service life.
Fits the E3D V5 and V6 and available in 12 and 24VDC!
There also a 5V available for those low...
24VDC Heater Cartridge
A 24VDC 40W heater cartridge with 1 meter leads. These are used in a number of hotends. High power ceramic heater cartridge with silicon insulated high temperature wires. If you have ordered an E3D and have a...
3.0mm Bowden Tubing
The bowden tubing is sold in 100mm sections.
What is a Bowden feed?
A quick explanation:
In the realm of 3D printing there are two separate ways to get your filament to the...
Block & Sock - V6 Upgrade Kit
Contains all you'll need to upgrade your standard E3Dv6 hotend to the new Sock & Thermistor Cartridge Block.
V6 cartridge-style heater block
Silicone Sock V6 (x3)
The new cartridge thermistor
Dyze Hot End Nozzles
Ready to install, comes with washer.
Sold as kit or stand...
E3D Embedded Bowden Coupling
Pneumatic fitting for the 3mm bowden and 1.75mm universal E3D V6.
E3D Heat Break
The E3D heat break is engineered to perfection. The heat break's task is to prevent all the wattage being generated in the heater block from traveling up the filament. E3D's heat break does this better than most...
E3D Heat Sink 1.75mm Universal
A spare 1.75mm Heat Sink for your E3D V6 in the event you need one...
E3D Heater Block
Essential for every 3D printer, the E3D v5, v6 and PT100 V6 heater blocks will make great additions to your printer.
One of the greatest improvements in the E3D V6 was the clamp on the thermistor and heater cartridge. The...
E3D Hotend V6 all metal kit
If you have a good thermistor, heater cartridge, and fan set-up this is a great way to save some money! Includes: .4mm nozzle Heatbreak Heatsink Heater block all screws and washers needed This kit includes everything...
E3D Nozzle Fun Pack
A fun collection of E3D-v6 ecosystem nozzles all conveniently packaged together in a tin case. Suitable for all E3D hotends except for Cyclops. This collection includes a wide range of nozzles to appease your exploration...
E3D nozzle wrench
A handy little wrench that fits the E3D nozzles (except Cyclops) and allows for less fuss removing and changing nozzles.
Stamped zinc plated...
E3D Spare Nozzles
A spare nozzle is not needed, but it sure makes life nice to have several spares!
The nozzles have been reworked by E3D since the V5 and the change is amazing! SMW3D noted a much smoother and consistent extrude even...
E3D V6 Groove Mounting Plate
A laser cut groove mount that allows the E3D V6 to be mounted to a custom extruder via two mounting holes.
Groove Mount Bowden Adaptor
Use this awesome little adapter in your extruder (such as the BondTech) to connect the hotend to the extruder via Bowden tubing. The groove mount profile is exactly like the E3D hotend top. Includes the...
Nozzle Cleaning Drill Bits
These handy little guys are great for cleaning and reshaping the nozzle on your 3D printer's hotend. Occasionally, you may crash into the bed and deform the nozzle tip or gather a piece of trash in the flow path, this is the...
Nozzle for Prometheus hotend. Comes in 0.3mm, 0.4mm, 0.6mm, and 1mm. Backwards compatable with Prometheus V1.1. 0.3mm length: 33mm 0.4mm length: 34mm 0.6mm length: 36mm 1mm length: 40mm...
PT100 temp sensor
The PT100 is a high temperature, highly accurate sensor to use on the E3D products. The sensor is a great alternative to the stock thermistor. This allows accurate temperature measurement up to 400C, and removes the need for...
The thermistor is an affordable way for the 3D printing community to monitor temperature.
2 pin connector (fits pins on shields such as the arduino and RAMPS)
V6 Molded Fan Duct
A molded fan duct for your E3D v6. Does not fit the V5.
V6 Silicone Socks - 3 pack
3 pack of non-stick silicone socks for e3d V6 style heater block with thermistor cartridges. They will not properly fit the screw-washed clamped thermistor style E3D-v6 Block. They fit the new cartridge style thermistor...
All prices are in USD. © 2017 SMW3D | Sitemap